Friday, December 04, 2015

How To Make A Small Pinecone Tree - Free How-To By Linda Walsh of Linda Walsh Originals

Since I had just finished my Linda's Blog post on the pine cone trees I had made I thought you might enjoy a step-by-step "How-to" on how to make one of your own.

My instructions on how to make a small pinecone tree of your own are shown below.

How To Make A Small Pinecone Tree


Supplies Needed

1 Can Spray Varnish or Lacquer
1- Green Styrofoam Cone 12"X4"
Package of Green Preserved Boxwood or Eucalyptus
1/2" Red Velvet Ribbon - 4 Yards
1/2" Covered Box Decorations - 1 Package
Florist Wood Picks With Wire - 1 Package
Red Berry Spray With Multiple Berries or Dried Red Floral Bulbs
Miniature White Floral Flowers (I used ones that looked like snow flakes)
Dried or Preserved Pine Cones of Various Shapes and Sizes
1/4" Pine Wood - 6" by 6"
3/4" Wood Dowel - 3" Long
Wood Screw - 1 1/2" Long
Wood Stain - 1 Small Can
Sand Paper
Dual Temperature Glue Gun
Glue Gun and Glue Sticks
Wire Cutters
Drill

Instructions



(Note - These instructions are for ADULT use only as they require the use of a hot glue gun.  Always use caution when working with any kind of hot glue gun.)

 1.  Cut a 6" by 6" square out of the 1/4" pine wood.  Round the edges and then completely sand it.
 2.  Cut a 3" long piece out of the 3/4" dowel.
 3.  Measure the center of the 6"x6" square and mark both the top of the square and bottom of the square with an X. 
 4.  Drill a small starter hole in the bottom of the 6"x6" square at the X for the wood screw.
 5.  Screw the 1 1/2" long wood screw to the bottom of the 6"X6" square until just the tip of it is showing through to the top.
 6.  Position the dowel on the X on the top of the 6"x6" square centering the tip of the wood screw at the center of the dowel.
 7.  Finish screwing the 6"x6" square to the wood dowel until they are both secure.
 8.  Stain the 6"x6" square and dowel with the wood stain. Let dry completely.
 9. Spray the 6”x6” square and dowel with the varnish or lacquer. Let dry completely.
10.  Position the center of the bottom of the green Styrofoam cone onto the dowel and push it down the dowel until the bottom of the Styrofoam cone is flat against the top of the 6"x6" square.  You may need to carve out a small amount of the center bottom of the green Styrofoam cone to get this area started.
11.  Remove the green Styrofoam cone from the dowel and glue all around the dowel and center bottom of the 6"x6"square using the low temperature setting of the dual temperature glue gun. Then re-position the green Styrofoam cone onto the dowel and center of the 6"x6" square.
12.  Glue the first layer of medium sized pine cones to the green Styrofoam cone using the low temperature setting of the dual temperature glue gun.   Position the pine cones so they abut one another and are pleasing to the eye.  Don't worry about gaps in between the pine cones as you will be filling these in with smaller pine cones.
13.  Continue gluing the pine cones in rows in this manner using the low temperature setting of the dual temperature glue gun until you reach the top of the green Styrofoam cone.
14.  Glue a medium sized pine cone to the top of the green Styrofoam cone using the low temperature setting of the dual temperature glue gun.
15.  Using the low temperature setting of the dual temperature glue gun glue the smaller pine cones in between the larger pine cones until all the gaps are filled.
16.  Spray the tree and pine cones with varnish or lacquer.  Let dry completely.
17.  Using the wire cutters cut several 2" - 3" pieces of the preserved boxwood or eucalyptus and then using the low temperature setting of the dual temperature glue gun glue the preserved box wood or eucalyptus amongst the pine cones until the arrangement is pleasing to the eye.
18.  Using the wire cutters cut the red berries so they are individual and then using the low temperature setting of the dual temperature glue gun glue the red berries amongst the pine cones until their placement is pleasing to the eye.
19.  Using the wire cutters cut the miniature white flowers into individual pieces and then using the low temperature setting of the dual temperature glue gun glue the miniature white flowers amongst the pine cones until their placement is pleasing to the eye.
20.  Stick the bottom center of the 1/2" covered box decorations with a floral pick and then stick them amongst the pine cones until their placement is pleasing to the eye.  Glue to hold if necessary using the low temperature setting of the dual temperature glue gun.
21.
  Cut sixteen 12" pieces of the 1/2" red velvet ribbon and then tie each into a bow.  Tie the wire of the floral pick around the center of the bow and then fasten the floral pick and bow amongst the pine cones until their placement is pleasing to the eye.  Glue to hold if necessary using the low temperature setting of the dual temperature glue gun.
22.  Congratulations - You're Done!


I also created a .PDF "Linda's How-Do-I Series How To Make A Small Pinecone Tree" e-book for this as well.


To view and download my free e-book please CLICK HERE. You'll be brought to Google Drive where you can view our free e-book. Then just download our free .pdf e-book by clicking on the down arrow in the top center.

For more information on all my free e-patterns, e-printables and e-books please CLICK HERE.

Please respect My Terms of Use:  All patterns, e-patterns, e-books, tutorials, how-to's, and e-products © 2004-2014 Linda Walsh Originals-Designs by Linda Walsh. All rights reserved, including downloading, mass producing, photocopying, enlargements, reductions,and all other forms of reproduction, website sharing, Email, RSS feeds, or any other means of redistribution. Commercial selling or reselling by any means, including eBay or any other website by permission only.

Products made from Linda Walsh Originals patterns, e-patterns, e-books, tutorials, how-to's, and e-products are intended for personal use for fun or small scale personal and business profit as long as you credit us with the design. Large scale commercial use (i.e. mass production) including wholesale distribution, catalog sales, and all other forms of large scale commercial production are by permission only. Items made from Linda Walsh Originals patterns, e-patterns, e-books, tutorials, how-to's, and e-products are intended for decoration only and are not intended for use by children. Not responsible for human error, individual workmanship, or printing errors in the E-books, E-products, tutorials, how-to's, patterns or the E-Patterns.

Copyright © 2004 - 2014 - All Rights Reserved - Written By Linda Walsh of Linda Walsh Originals and Linda's Blog. Linda is a doll maker and doll pattern designer. http://lindawalshoriginalsshop.com/

No comments:

Post a Comment